I gotta say that I really like the look of the steelies, just as they are TBH
1966 C10 build
- Thread starter AlbertaZ06
- Start date
I don't mind those wheels Dalen. This is not to be an insult but they look a bit like my Ford diesel wheels.View attachment 80306View attachment 80307
They don’t look like much, but worth a trip to Calgary to pick upA set of original steel wheels that clear disk brakes! Off a 71 4x4, actually it’s a hard find and keeping the original look. Just need to find some oem hubcaps. View attachment 80308I’m also growing attached to “loaner wheels”
. I talked my buddy into considering selling them to me. Not sure on this one
That’s a nice clean old Ford
. The wheels do look similar!
Got the box on today! Kinda sketchy doing it myself
. But it’s on the frame, still need to install the cross braces and bolt down the box. Love the long bed stepside 
. To many people take these trucks, and cut them into a short bed. Can’t wait to load up a full load of lumber in the back of this old girl 
of course when that price of lumber goes back down
Looking great Dalen. Not holding my breath for lumber prices to drop any time soon though. 
It’s scary! Hopefully soon the price goes down. My neighbors a contractor, and jobs are starting to get dropped, because it’s $30K + in cost of materials now.Looking great Dalen. Not holding my breath for lumber prices to drop any time soon though.
There's a few out there losing their shirts because they signed contracts before the increase for house builds and didn't buy the lumber back then. It is scary.
. While waiting on a shifter, and carpet for the C10, I pulled a 94 LT1 Corvette motor out of a boat for a friend to get sent away for a rebuild! Fun stuff around the garage . I’m really liking the 2 1/2” Front drop and 3” rear drop on the C10!! Sitting nicely, and not to low.Attachments
C10 looks great. Now for a Black Cherry paint job... lol...
. Never noticed when I installed the transmission that it had to much of a gap..... Long story short, it’s back in and cost a extra $200, had to install some shims to properly space it. Lesson learned for a stick shift clutch kinda guy .
Finally got the shifter and installed it
No more 7/16” wrench to move this truck around . Went with American Shifter. I wanted a Lokar (back ordered everywhere), but think it’s close to the same and looks just as cool .
. Someone put down deck board before me in the box, so it’s missing the original metal stingers between the boards, it’s not the nicest look but functional until I redo the box. I finally got the gas cap mounted in the box as well, no more coffee can covering the gas tank up and the smell gas fumes gone 
IMO, wood should look like wood and not be covered with paint. Stain it a light to medium brown, give it a couple coats of Thompson's Water Seal and I'll bet it will look perfect.
Agreed
. Was going to paint it, but think the stain would add a nice contrast
R
RockyPM
Looking Great Dale! Wish i had your skills, and garage! Hopefully will see it in person one of these days.
Busy week! But the C10 is on the road!! Stained the box boards, cut and hacked the gas pedal to fit, installed the carpet and seat, hauled it to get the wheel alignment, test drove it, broke down, fix it, and some tuning on the fly. Fun stuff
. So far I still got oil pressure and runs and drives great . The wife took it out for 3 hours, and now says it hers . What a fun build!! While doing this project in the C10 world, I met some good people, learned a bunch on the old trucks and had a blast!!. I have few little things to clean up and do, but the C10 build was a success . I’m kinda lost now with the whole fleet running and nothing to do. Not sure what next...... C5 turbo build, C3 LS swap, LS Swap Square body C10, Electric swap MG? So many ideas, I have been on Kijiji & Facebook marketplace, see what’s out there. Just enjoying working away at any project in the garage teaching my 3 boys the passion of building stuff and having fun while doing it.
A man with a passion. Good on ya Dalen. I spend a lot of time in my cave working on things non mechanical...lol... When I think I am running out of stuff to do, I invent new things. A month ago I was caught up in my hobbies and out of nowhere decided I would build a Viking axe for my fishing and hunting buddy's birthday. Enjoyed it so much, I have two more on the go now but then got sidetracked and decided I would build a greenhouse with about 20 old mobile home windows I came across. I learned quick that as well as not being a mechanic, I have a lot to learn about carpenter work too... LOL... Measure twice/cut once.... Here's a pic of the axe I built. Cut the head out of an old splitting axe and carved the handle out of a piece of 2x4. Hardest part of the whole thing was learning how to braid the leather. Youtube is my friend
now.
now.
Last edited:
Very cool
. It’s always rewarding seeing the finished product of what ever being worked on !I will have to make a cruise out to pine lake area sometime
Definitely... on both counts. 2 km of gravel though so visitors seldom bring their Vettes...lol...Very cool
I will have to make a cruise out to pine lake area sometime
I came across this on my search
. 1974 Manta Montage kit car. All set up with Corvette suspension, tube frame built for a LS. Needs a lot of work, and $7500 is a little tight for me right now, hopefully it would be available in a few months!Similar threads
-
36mo later still waiting for my allocation, and from 2LT to 1LT
- Started by typer100
- Replies: 43
-
-
-
-
