Recent content by C6Vette09

  1. C6Vette09

    FS: $5500 OBO HRE P40 w/tires

    Just bought these rims in Sept 2011. This tire package new would be easily $8000K or more. I'm asking $5500. OBO. The rims are 20X9.5 front / 20X11 rears. The tires are Extreme Contact Continentals. Both rim and rubber are in mint condition. They will be available next week. Buyer pays...
  2. C6Vette09

    Finally... Car will so be done

    Okay! Mums the word! LOL!
  3. C6Vette09

    Finally... Car will so be done

    Great conversation! It was nice meeting with you too. The heads and intake, will be ready for you in January! :D
  4. C6Vette09

    Finally... Car will so be done

    The boys at Champion, did a great job of getting the car set up, so that I can be back on the road for next week. I have a 3.4" pulley on the system now, so I suspect that I might exceed the 13 lbs of boost, that I had last time. As long as it can take the extra boost [and it most definitely...
  5. C6Vette09

    Finally... Car will so be done

    I think the numbers for this set-up, should be north of 714 RWHP. I wasn't able to exceed 714 last time, because of the cracked cylinder sleeve, and the fact that I lost 20% compression in two cylinders [5 and 7]. :coolgleam: I'll post the results once the car has been dyno'd... :D
  6. C6Vette09

    Coming soon from ECP ---2003 Z06-TVS2300 build

    Very nice build Manny! It looks great! :D
  7. C6Vette09

    Finally... Car will so be done

    Motors' in... Motors' in and running fine. It'll be dyno'd Monday or Tuesday of next week...
  8. C6Vette09

    Finally... Car will so be done

    Everyone meet Wilson! Making great progress motor should be in very soon ... Wilson's new home... Wilson is in...
  9. C6Vette09

    Finally... Car will so be done

    Well, I think ultimately the sleeve itself wasn't "good" if you will, because all of the pistons looked fine. There was definitely no consistency in terms of cylinder sleeve thickness compared to an LS7 block. Some guys have had no problems doing what I did [at least in a the short term], with a...
  10. C6Vette09

    Finally... Car will so be done

    New Ls7 427 just arrived My forged Ls7 427 just arrived today
  11. C6Vette09

    Finally... Car will so be done

    Well, I've always been interested in changing to a 427 set-up and the opportunity presented itself, unexpectedly. During the Arizona type heat wave we had a few weeks ago [in Toronto], the car started to overheat. After doing a leak-down test, the boys found that cylinders 5 & 7 were down 20%...
  12. C6Vette09

    Finally... Car will so be done

    Car's going in for surgery in the next few days... I'm installing a forged 427 LS7 short block. I'm going to use my Ls3 ported heads, fast intake and 102 TB. This set-up should have a lot of torque once it's done. With the stock block, the car dyno'd 658 rwhp and 574 rwtq. It'll be interesting...
  13. C6Vette09

    New HRE P40

    Just got my new HRE P40's in today...
  14. C6Vette09

    New Ride on the Island

    Looks great! Congrats ! :D
  15. C6Vette09

    speeding

    I was followed very close [ about a block away] five times last year. When in my truck [Jeep SRT8] I never get followed home. I definitely agree, that if you drive a Vette or any other high end sports car, you'll get unfairly profiled! I would say that the majority of Cops still like to put a...